Want to get rid of that builder grade faux wood paneling on your kitchen island or peninsula? You know the stuff. It resembles those wood panels that used to be on the sides of station wagons. I’ve had it in every kitchen I’ve owned. But I’ve learned that I don’t have to live with it. And neither do you.
This peninsula update is the first step of many to come in a mini DIY remodel that I’m about to undertake in my small, non-functional kitchen. I’ve had smaller kitchens, but my current kitchen, hands down, wins the award for the least functional. It also ranks right up there with the least aesthetically pleasing.
So here are my before pictures. Pretty standard as far as peninsulas go. This kitchen is one big ball of patterned brown. I love brown, but there are brown patterns that fight each other in the oak grain, the flooring and the countertops. Makes me dizzy. This kitchen is not a safe place for anyone who is prone to seizures—that’s for sure.
I’ve been collecting posts on Pinterest for kitchen ideas, and to give credit where credit is due, I copied this design from “Remodelaholic”. And I combined her project with a photo I saw on “DIY Network”. This transformation can be done with basic carpentry skills, and isn’t all that expensive.
Step one was to remove the corner trim piece so I could pry back the existing paneling and locate the studs, water lines and electrical wires. My dishwasher is in my peninsula, so I was aware that the potential existed for an electrical shock or a flash flood if my nail hit just the right spot.
Unfortunately the installer for my new dishwasher had to remove some studs in order to get it to fit into the space where the old one was. That leaves me with only a few studs to attach my boards to. I knew that was going to be my biggest challenge. However, I was relieved to find no water lines running through the studs like I had in my last house, and there were only two electrical wires that were going to be relatively easy to avoid. Here’s one of them.
So I marked my stud locations on my counter top with some tape, and I taped another area to mark a board from the back of a cabinet that I could use to nail into. And of course, there will always be a 2 x 4 on the floor, on the outside corners and against the wall that were used in framing.
I had to remove a piece of baseboard on the wall adjacent to the peninsula since it was going to have to be trimmed down afterwards.
The only other out-of-the-ordinary item I had to deal with, was an electrical outlet that I had to move up about 1/2″.
I decided to use bead board paneling for this project, and Lowe’s had a new kind that looked like traditional bead board on steroids. The routed groves were much larger and farther apart. A 4′ x 8′ sheet of traditional bead board paneling ran around $20. The more unique version that I decided to use was $30 a sheet. The extra $10 was worth it to me.
Lowe’s will cut plywood for their customers, and so will Home Depot. Not only does it save me the hassle of cutting it, but a 4′ x 8′ sheet won’t fit in my tin can of a car. I had them make me four panels which required four cuts. The first two cuts were free, and the second two cost me 25 cents. Again, worth it. I also had a large scrap piece leftover to use on another project.
I had the panels cut to a size that was 1/4″ shorter than the actual height of my counter tops so that I could mount them off the floor a bit. Dishwasher + leak = potential water on the floor at some point. Cutting it short also allowed for any wonkiness as far as the possibility of the sheets not being cut perfectly square (sorry Lowe’s) or my floors/counters etc…not being square (sorry house).
So I attached the bead board to the peninsula, setting it on a ruler to raise it while I hammered. I’m happy to report I only hit my thumb once, but I’ll admit I did bend a handful of nails that had to go in the garbage. I also broke two drill bits while pre-drilling. Like I said, I’m not a carpenter. I also used a level to make sure each sheet was plumb.
Here’s a photo after the bead board was attached. Since I didn’t have much of a selection of studs to hammer into, some of the pieces only had one nail on top and one on the bottom, but I knew when I added the trim, some of those nails would also be penetrating the bead board to hold it on too. The trim itself would also help secure it.
I had to trim around the outlet, and I also had to shave down part of the toe kick that extended past the end of the cabinet in order for the bead board to lay flat against the cabinet.
Next, I added 1 x 4 pieces of MDF that I cut down from a leftover sheet I already had, and attached those. I also kept those up off the floor. MDF and water do not mix.When MDF gets wet, it puffs up like a toasted marshmallow.
Next came the horizontal pieces. I had to cut a hole in the trim piece that went around the outlet.
Here’s how it looked with the horizontal pieces added.
The bottom board is a 1 x 8, so that once I put the baseboard on, there will be a reveal equal to the rest of the 1 x 4 trim.
The next step was to install the remaining vertical boards. These will cover the areas where the sections of bead board paneling meet.
The previous photo shows that my vertical board placement didn’t line up with any studs (marked by the blue tape on the counter top). In order to attach these two pieces, I just pre-drilled at an angle so my nails would go into the horizontal pieces that were nailed into studs. This is where I managed to snap my last 1/16 bit. Sigh.
A suggestion from the “Remodeloholic” post, was to round over the edges of the trim boards, so that once installed, there is an intentional space where the trim boards meet. That way, there’s no need to caulk or putty those areas.
Here all of the trim pieces were installed.
Next came the baseboard. The baseboard is the only piece placed directly on the floor to cover the gaps from the bead board, the corner trim and the 1 x 8’s. It would be simple enough to replace if it were to get wet.
In order to keep costs down on my projects, I usually buy “lesser” quality pine boards and then spackle over any knots or dings at the same time I putty all my nail holes. I sand and paint, and the imperfections are impossible to find afterwards.
Next a coat of primer.
After the primer dried, I caulked every place that the trim met the bead board, and along the top of the baseboard. This is an important step, and makes everything professional looking.
Then I painted everything with two coats of paint, sanding in between coats. Finished!
Now the traditional before and afters.
Since I had some of the pine boards and MDF already, I don’t know exactly what this project cost, but I would approximate not more than $50, with $30 of that being for the bead board.
A cheaper version would be to leave out the bead board and mount the trim directly onto the existing faux wood paneling. Give the paneling a light sand, a good primer and a good quality paint and you’re on your way. I’ve done that too!
Honestly, the worst part of this project was the major splinter I got in my hand when picking out the wood. It was all smooth sailing after that.
Author’s edit: And here she is after surviving nearly two weeks in the palm of my hand. My daughter, Sophie, was my splinter remover, but she moved to Los Angels. Now I’m on my own in the foreign object removal department. (Thus the two week hibernation period.)
Now on to another cabinet…
This post was written by Tracy Evans who is a Journeyman Painter and Certified Home Stager /Redesigner. Feel free to visit her website at www.HelpAtHomeStaging.com to view more before and after pictures of her projects. And if you enjoy gardening, you may want to visit her gardening blog at MyUrbanGardenOasis.